Inflatable boat D- Rings, Glue-ON Tie Downs for inflatable dinghy.TOWING D-RING for inflatable boats on PVC and HYPALON patches
Patch kits , Glue, Adhesive for Inflatable Boats, dinghies .Available for PVC , Hypalon (synthetic rubber (CSM)) Inflatable boats.
3 step Ladder for Inflatable Boat, Ribs or aluminum boats. No more struggles getting back on board of Inflatable Boat. Boat Ladder incorporated contour design hugs the hull for side boarding and vinyl sleeve for hull fabric protection.Dinghy ladder great for our snorkeling trips or diving.
Inflatable Thwart (seat) for 7.5 ft - 11 ft inflatable fishing boats. Color is black This seat will fit between inflatable tubes/ chambers of inflatable boat, and can be inflated more or less to fit your boat. Made of Heavy duty 1000 denier polyester re-enforced PVC Weight - 1100 g/m Thickness - 0.9mm Seat diameter - 11" (25 cm). Thwart is 29" (80 cm) long.
Easy to install, underseat storage bags with over the seat cushions not only provide a convenient storage place, but also protect your most valuable assets from being bumped on choppy water by a hard-surface boat bench.
Underseat detachable storage bag for 12 ft inflatable boat with cushion designed to be unfastened withing seconds. For better sitting comfort there is also ergonomic cushion.
Drain plug set for inflatable boat designed to fit 39 mm opening through a solid plywood,wood or aluminum transom. Fits 4 cm (1.5") thick transoms.
Drain plug set for inflatable boat designed to fit 39 mm opening through a solid plywood,wood or aluminum transom. Fits 3 cm (1") thick transom of inflatable dinghy
INFLATABLE BOAT FRONT STORAGE BAG BLUE fits 6 ft - 12 ft Inflatable boat.
INFLATABLE BOAT FRONT BOW STORAGE BAG fits 6 ft - 12 ft Inflatable boat. Color is light grey.
1 x GREY SEAT HOOK STRAP PATCH FOR INFLATABLE BOATS THE SAME GOOD STRONG QUALITY SEAT HOOK STRAP PVC PATCH THAT IS ON INFLATABLE BOATS. SIZE 35M X 12CM. SEAT STRAP WOVEN FABRIC 20CM
OAR LOCK for INFLATABLE BOAT in black color. Made of ABS plastic.Designed to be glued onto PVC / Hyplon inflatable boat.Can be used as a replacement for existing oar locks or can be used to add new oar locks to inflatable dinghy.
Engine mounts for inflatable boat.Made of heavy duty plastic.Color is light gray.Can be used as a replacement for worn engine mounts or can be used to add new to inflatable dinghy.Designed to be affixed to the transom ,outside, within two inches of the top.
Engine mount PAD for inflatable boat. Made of heavy duty plastic.Color is BLACK .Can be used as a replacement for worn engine mounts or can be used to add new to inflatable dinghy. Designed to be affixed to the plywood or fiberglass transom ,outside, within two inches of the top.
Replacement Halkey Roberts Valve for Inflatable boat (H-R valve)
Motor mount for inflatable dinghy fits most sizes of inflatable boats. Steel bracket Corrosion resistant coatings protect metal components against degradation. Motor mount kit designed for outboards up to 3.5 HP petrol or electric trolling motors.Outboard engine braket kit comes with 4 x Pedestals & 30g tube of glue for PVC inflatable boats.
Motor mount for inflatable boats- bow or sternt mount.Fit most sizes of inflatable boats. Stainless steel bracket. Fits outboards up to 3.5HP petrol or electric trolling motors.
2 step Ladder for Inflatable Boat, Ribs or aluminum boats. No more struggles getting back on board of Inflatable Boat. Boat Ladder incorporated contour design hugs the hull for side boarding and vinyl sleeve for hull fabric protection.Dinghy ladder great for our snorkeling trips or diving.
REINFORCED STRONG QUALITY OAR LOCK for INFLATABLE BOATS. Made of ABS plastic.
THE SAME GOOD STRONG QUALITY HANDLES THAT ARE ON Aquamarine INFLATABLE BOATS. Designed for PVC inflatable boats. Color is grey or black .
The bow Storage Bag helps keep clutter off the floor of your inflatable boat by delivering much needed out-of-the-way storage. Perfect for storing life jackets, flares, camera , first aid kit and other essential gear.Designed to fit in the bow of a boat, triangular shaped
Plywood seat for 12.4 Aquamarine Inflatable boat Also will fit similar inflatable boats
Inaccurate air pressure of chambers or air floor can cause low performance of inflatable boat .Overpressure can be cause blow-out of your inflatable. To prevent these events from happening it is important to maintain proper air pressure. Bravo air pressure gauge designed to fit into Halkey-roberts(H-R) valve.
Halkey Roberts (H-R) Air Valve will fit most inflatable boats, river rafts and RIBs. Halkey-roberts(H-R) valve comes in three parts. One inside part , one outside part and valve cap.
Replacement oar lock pin for Aquamarine inflatable boats and similar inflatables with ABS plastic oar locks. Stanley steel oar shaft diameter -10 mm
Halkey-Roberts valve adapter.Standard equipment with foot pump.Spare nozzles made to fit 20.5 mm -21 mm inner diameter pump hose. Please measure diameter of pump hose and compare to provided above. Halkey robert valve adapter is threaded as shown in the picture.
Inflatable Thwart for 14' river rafts, boats. Made of 0.9mm reinforced PVC Color is Red Comes with H-R valve instaled and two D-rings
Inflatable Thwart for 12' river rafts, boats. This seat will fit between inflatable tubes/ chambers of the whitewater river raft, and can be inflated more or less to fit your boat. Blue color
Aluminum bench seat for 7.4 feet (230)/8.8 feet (270)/9.8 feet (300)/11 feet (330) aquamarine Inflatable boat Also will fit similar inflatable boats
Inflatable Thwart (seat) for 14 ft inflatable fishing boats. This seat will fit between inflatable tubes/ chambers of inflatable boat, and can be inflated more or less to fit your boat. Made of Heavy duty 1000 denier polyester re-enforced PVC Weight - 1100 g/m Thickness - 0.9mm Color is grey.
Inflatable Thwart (seat) for 12.5ft inflatable fishing boats. This seat will fit between inflatable tubes/ chambers of inflatable boat, and can be inflated more or less to fit your boat. Made of Heavy duty 1000 denier polyester re-enforced PVC Weight - 1100 g/m Thickness - 0.9mm Color is grey. Seat diameter - 13 inches (34cm). Thwart is 33 inches (84 cm) long.
STRONG QUALITY ANCOR TIE OFFS THAT ARE ON FISHING INFLATABLE BOATS
Inflatable Thwart (seat) for 7.5 ft - 11 ft inflatable fishing boats. This seat will fit between inflatable tubes/ chambers of inflatable boat, and can be inflated more or less to fit your boat. Made of Heavy duty 1000 denier polyester re-enforced PVC Weight - 1100 g/m Thickness - 0.9mm Color is grey. Seat diameter - 11" (25 cm). Thwart is 28" (70 cm) long.
Aluminum bench seat for 14' aquamarine Inflatable boat. Will fit similar inflatable boats
Aluminum bench seat for 12' aquamarine Inflatable boat Also will fit similar inflatable boats
Designed to hang from an inflatable boat's rigid seat, The Underseat Storage Bag helps keep clutter off the floor of your inflatable boat by delivering much needed out-of-the-way storage. Perfect for storing life jackets, flares, camera , first aid kit and other essential gear. Underseat storage bags for AQUAMARINE boats . fit seats dimensions: 37.5" x 8" or 39.5" x 8"
Removable Bow Mount platform for Inflatable boats and dinghies. Designed for bow mount trolling motors, fishing finder, GPS, phone mount, cup holder or VHF radio . Ideal inflatable boat mount if you require the ability to easily remove or attach your accessories. Bow mount platform also provides extra useful space on your inflatable boat.Made of stainless steel 0.8 inch tube and one inch marine plywood.
Hinged Motor Mount for Canoe. Motor mount made of strong rigid aluminum and can hold engine up to 3 HP. Canoe Motor mount is also 30 inches long and used on just about all canoes.
Anchor patch tie off for inflatable boat. Anchor tie off glue on patch size L:24cm(9 1/2 in) x W:12.5 cm (5 in) x H:6 cm (2.5 in)
Anchor patch tie off for inflatable dinghy. Made of PVC Plastic. Color is black.
Inside engine mount motor pad plate for inflatable boats the same good strong quality motor mount pad that are on inflatable boats.Material- Aluminum . Color -Black.
Removable Center fin fits for inflatable stand up paddle SUP boards.Usually affixed to the bottom of the Inflatable Stand Up Paddle Board.
Engine mount motor pad plate for inflatable boats the same good strong quality motor pad that are on inflatable boats. Inside-mounted Transom Outboard Plate for Inflatable Boats comes in gray color. Protects inflatable boat transom.
LIFTING HANDLE / CLEAT FOR INFLATABLE BOATS.COLOR IS GRAY.
LIFTING HANDLE / CLEAT FOR INFLATABLE BOATS.COLOR IS BLACK.
Drain plug set for inflatable boat designed to fit 45 mm opening through a solid plywood, wood, aluminum or fiberglass transoms. Fits 3 cm (1") thick transom of inflatable dinghy
Drain plug set for inflatable boat designed to fit 45 mm opening through a solid plywood, wood , aluminum or fiberglass 1.5 inch transoms.
